|
Post by elliamaria on Mar 29, 2018 9:09:59 GMT -5
Hello, I recently started using Alumilite Clear , and I have a few questions about adding in the dyes. I use the Alumilite liquid dyes to my Clear but I always add them after I mix part A and part B. Now I noticed in some forum posts that it's possible to add the dye to part A, and then mix in part B. Would it make a difference in the final product which way you mix your dyes in? Is one way better than the other or is one way preferred in certain color combinations? Any input is welcome Thank you! Elliamaria
|
|
|
Post by carol - Alumilite Corp on Mar 29, 2018 12:19:36 GMT -5
Elliamaria,
Good Morning ...
The dyes are added to the “A” side by weight up to 5% is generally how it is put into the resin Elliamaria. I think that it is put in the A side because some of the resins have an off color B side (not clear) so it enabled you to see a shade that may be close to what you are looking for. It is a bit easier to get a good mix putting it in the A side as you can disperse it well and thoroughly with a little less time restraint. It allows you to take a little longer as the two sides are not put together so you would be in your open time perhaps having to hurry the mix/blend.
Regards,
Carol
|
|
|
Post by elliamaria on Mar 29, 2018 19:02:12 GMT -5
Hi Carol,
I'm sorry if this sounds a little silly but how would that work if I have 2-3-4 different colors? Do I set up that many cups with A side? What I'm having a problem is that I mix 2 or 3 colors in 2 or 3 cups that have already premixed A and B. Then I add powders to the cups. But that slows me down so much that I create bubbles in the scales I make.
Thank you!
|
|
|
Post by carol - Alumilite Corp on Apr 3, 2018 9:33:33 GMT -5
Hello Elliamaria,
You want them to have a multi color/swirled look? If that is what you are after the best way is to mix the resin as usual, then take some dye and put a small amount (different colors) on the end of each different stir stick. You will then swirl (NOT mix/blend) those colors this will give you a beautiful swirly pattern of whatever colors you have chosen. If I have misunderstood you and your are looking for layer colors like a parfait, let me know dear.
Warmest Regards,
Carol
|
|
|
Post by Woodchuck on Apr 6, 2018 9:43:14 GMT -5
Hi Carol,
I just started making shave brush handles and have a similar question. Trying to make a yellow (closer to gold) handle with blue swirled into it so I mixed the yellow and then tried adding blue. When I added the blue using a stir stick, swirling not mixing, it almost immediately created green. How do I prevent the mixing?
Thank you!
|
|
|
Post by carol - Alumilite Corp on Apr 11, 2018 12:25:54 GMT -5
Good Day WoodChuck,
Yes the process would be essentially the same. The yellow dye however is not a gold looking yellow, you may want to try the Gold Metallic Powder or one of shades of Gold Alumidust. The dyes are very concentrated and can over power the dust if a blend takes place with just a little mixing. The best way to do this is use the gold dust and the blue dust if you don't want it to go completely solid or using the gold powder, then making a swirl with the blue dye on the end of stick through the gold powder.
Regards,
Carol
|
|
|
Post by elliamaria on Apr 16, 2018 1:26:02 GMT -5
Hi Carol, I will try that! I am always afraid that I will run out of time. I was having some issues with bubbles on the top of my scales, and I can't figure out why I have them. I made a whole new set of molds, and I'm about to try them with the methods you recommended. Do you think that my bubbles could be because of high temperature in my room? It is usually about 76-78 degrees when I cast Thank you again for all your help!
|
|
|
Post by carol - Alumilite Corp on Apr 24, 2018 9:11:16 GMT -5
Elliamaria,
Are you degassing your silicone molds prior to putting them under pressure my dear? I don't think that the temperatures would do the bubbles, moisture perhaps?
Please call me Elliamaria if you would like to.
Have a wonderful day your are most welcome!
Warmest Regards,
Carol
|
|